patch-2.3.40 linux/drivers/ieee1394/pcilynx.h
Next file: linux/drivers/ieee1394/raw1394.c
Previous file: linux/drivers/ieee1394/pcilynx.c
Back to the patch index
Back to the overall index
- Lines: 529
- Date:
Thu Jan 20 10:44:46 2000
- Orig file:
v2.3.39/linux/drivers/ieee1394/pcilynx.h
- Orig date:
Wed Dec 31 16:00:00 1969
diff -u --recursive --new-file v2.3.39/linux/drivers/ieee1394/pcilynx.h linux/drivers/ieee1394/pcilynx.h
@@ -0,0 +1,528 @@
+#include <linux/config.h>
+
+#define PCILYNX_DRIVER_NAME "pcilynx"
+#define PCILYNX_MAJOR 177
+
+#define PCILYNX_MINOR_AUX_START 0
+#define PCILYNX_MINOR_ROM_START 16
+#define PCILYNX_MINOR_RAM_START 32
+
+#define PCILYNX_MAX_REGISTER 0xfff
+#define PCILYNX_MAX_MEMORY 0xffff
+
+#define PCI_DEVICE_ID_TI_PCILYNX 0x8000
+#define MAX_PCILYNX_CARDS 4
+#define LOCALRAM_SIZE 64
+
+#define NUM_ISORCV_PCL 4
+#define MAX_ISORCV_SIZE 2048
+#define ISORCV_PER_PAGE (PAGE_SIZE / MAX_ISORCV_SIZE)
+#define ISORCV_PAGES (NUM_ISORCV_PCL / ISORCV_PER_PAGE)
+
+/* only iso rcv uses these definitions so far */
+#define CHANNEL_LOCALBUS 0
+#define CHANNEL_ASYNC_RCV 1
+#define CHANNEL_ISO_RCV 2
+#define CHANNEL_ASYNC_SEND 3
+
+typedef int pcl_t;
+
+struct ti_lynx {
+ int id; /* sequential card number */
+
+ spinlock_t lock;
+
+ struct pci_dev *dev;
+
+ struct {
+ unsigned reg_1394a:1;
+ u32 vendor;
+ u32 product;
+ } phyic;
+
+ enum { clear, have_intr, have_aux_buf, have_pcl_mem,
+ have_1394_buffers, have_iomappings } state;
+
+ /* remapped memory spaces */
+ void *registers;
+ void *local_rom;
+ void *local_ram;
+ void *aux_port;
+
+
+ atomic_t aux_intr_seen;
+ wait_queue_head_t aux_intr_wait;
+
+ void *mem_dma_buffer;
+ struct semaphore mem_dma_mutex;
+ wait_queue_head_t mem_dma_intr_wait;
+
+ /*
+ * use local RAM of LOCALRAM_SIZE (in kB) for PCLs, which allows for
+ * LOCALRAM_SIZE * 8 PCLs (each sized 128 bytes);
+ * the following is an allocation bitmap
+ */
+ u8 pcl_bmap[LOCALRAM_SIZE];
+
+#ifndef CONFIG_IEEE1394_LYNXRAM
+ /* point to PCLs memory area if needed */
+ void *pcl_mem;
+#endif
+
+ /* PCLs for local mem / aux transfers */
+ struct {
+ pcl_t start, cmd, mod, max;
+ } mem_pcl;
+
+ /* IEEE-1394 part follows */
+ struct hpsb_host *host;
+
+ int phyid, isroot;
+
+ spinlock_t phy_reg_lock;
+
+ pcl_t rcv_pcl_start, rcv_pcl;
+ void *rcv_page;
+ int rcv_active;
+
+ pcl_t async_pcl_start, async_pcl;
+ struct hpsb_packet *async_queue;
+ spinlock_t async_queue_lock;
+
+ struct {
+ pcl_t pcl[NUM_ISORCV_PCL];
+ u32 stat[NUM_ISORCV_PCL];
+ void *page[ISORCV_PAGES];
+ pcl_t pcl_start;
+ int chan_count;
+ int next, last, used, running;
+ struct tq_struct tq;
+ spinlock_t lock;
+ } iso_rcv;
+};
+
+/* the per-file data structure for mem space access */
+struct memdata {
+ struct ti_lynx *lynx;
+ int cid;
+ int aux_intr_last_seen;
+ enum { rom, aux, ram } type;
+};
+
+
+
+/*
+ * Register read and write helper functions.
+ */
+inline static void reg_write(const struct ti_lynx *lynx, int offset, u32 data)
+{
+ writel(data, lynx->registers + offset);
+}
+
+inline static u32 reg_read(const struct ti_lynx *lynx, int offset)
+{
+ return readl(lynx->registers + offset);
+}
+
+inline static void reg_set_bits(const struct ti_lynx *lynx, int offset,
+ u32 mask)
+{
+ reg_write(lynx, offset, (reg_read(lynx, offset) | mask));
+}
+
+inline static void reg_clear_bits(const struct ti_lynx *lynx, int offset,
+ u32 mask)
+{
+ reg_write(lynx, offset, (reg_read(lynx, offset) & ~mask));
+}
+
+
+
+/* chip register definitions follow */
+
+#define MISC_CONTROL 0x40
+#define MISC_CONTROL_SWRESET (1<<0)
+
+#define PCI_INT_STATUS 0x48
+#define PCI_INT_ENABLE 0x4c
+/* status and enable have identical bit numbers */
+#define PCI_INT_INT_PEND (1<<31)
+#define PCI_INT_FORCED_INT (1<<30)
+#define PCI_INT_SLV_ADR_PERR (1<<28)
+#define PCI_INT_SLV_DAT_PERR (1<<27)
+#define PCI_INT_MST_DAT_PERR (1<<26)
+#define PCI_INT_MST_DEV_TIMEOUT (1<<25)
+#define PCI_INT_INTERNAL_SLV_TIMEOUT (1<<23)
+#define PCI_INT_AUX_TIMEOUT (1<<18)
+#define PCI_INT_AUX_INT (1<<17)
+#define PCI_INT_1394 (1<<16)
+#define PCI_INT_DMA4_PCL (1<<9)
+#define PCI_INT_DMA4_HLT (1<<8)
+#define PCI_INT_DMA3_PCL (1<<7)
+#define PCI_INT_DMA3_HLT (1<<6)
+#define PCI_INT_DMA2_PCL (1<<5)
+#define PCI_INT_DMA2_HLT (1<<4)
+#define PCI_INT_DMA1_PCL (1<<3)
+#define PCI_INT_DMA1_HLT (1<<2)
+#define PCI_INT_DMA0_PCL (1<<1)
+#define PCI_INT_DMA0_HLT (1<<0)
+/* all DMA interrupts combined: */
+#define PCI_INT_DMA_ALL 0x3ff
+
+#define PCI_INT_DMA_HLT(chan) (1 << (chan * 2))
+#define PCI_INT_DMA_PCL(chan) (1 << (chan * 2 + 1))
+
+#define LBUS_ADDR 0xb4
+#define LBUS_ADDR_SEL_RAM (0x0<<16)
+#define LBUS_ADDR_SEL_ROM (0x1<<16)
+#define LBUS_ADDR_SEL_AUX (0x2<<16)
+#define LBUS_ADDR_SEL_ZV (0x3<<16)
+
+#define GPIO_CTRL_A 0xb8
+#define GPIO_CTRL_B 0xbc
+#define GPIO_DATA_BASE 0xc0
+
+#define DMA_BREG(base, chan) (base + chan * 0x20)
+#define DMA_SREG(base, chan) (base + chan * 0x10)
+
+#define DMA0_PREV_PCL 0x100
+#define DMA1_PREV_PCL 0x120
+#define DMA2_PREV_PCL 0x140
+#define DMA3_PREV_PCL 0x160
+#define DMA4_PREV_PCL 0x180
+#define DMA_PREV_PCL(chan) (DMA_BREG(DMA0_PREV_PCL, chan))
+
+#define DMA0_CURRENT_PCL 0x104
+#define DMA1_CURRENT_PCL 0x124
+#define DMA2_CURRENT_PCL 0x144
+#define DMA3_CURRENT_PCL 0x164
+#define DMA4_CURRENT_PCL 0x184
+#define DMA_CURRENT_PCL(chan) (DMA_BREG(DMA0_CURRENT_PCL, chan))
+
+#define DMA0_CHAN_STAT 0x10c
+#define DMA1_CHAN_STAT 0x12c
+#define DMA2_CHAN_STAT 0x14c
+#define DMA3_CHAN_STAT 0x16c
+#define DMA4_CHAN_STAT 0x18c
+#define DMA_CHAN_STAT(chan) (DMA_BREG(DMA0_CHAN_STAT, chan))
+/* CHAN_STATUS registers share bits */
+#define DMA_CHAN_STAT_SELFID (1<<31)
+#define DMA_CHAN_STAT_ISOPKT (1<<30)
+#define DMA_CHAN_STAT_PCIERR (1<<29)
+#define DMA_CHAN_STAT_PKTERR (1<<28)
+#define DMA_CHAN_STAT_PKTCMPL (1<<27)
+#define DMA_CHAN_STAT_SPECIALACK (1<<14)
+
+
+#define DMA0_CHAN_CTRL 0x110
+#define DMA1_CHAN_CTRL 0x130
+#define DMA2_CHAN_CTRL 0x150
+#define DMA3_CHAN_CTRL 0x170
+#define DMA4_CHAN_CTRL 0x190
+#define DMA_CHAN_CTRL(chan) (DMA_BREG(DMA0_CHAN_CTRL, chan))
+/* CHAN_CTRL registers share bits */
+#define DMA_CHAN_CTRL_ENABLE (1<<31)
+#define DMA_CHAN_CTRL_BUSY (1<<30)
+#define DMA_CHAN_CTRL_LINK (1<<29)
+
+#define DMA0_READY 0x114
+#define DMA1_READY 0x134
+#define DMA2_READY 0x154
+#define DMA3_READY 0x174
+#define DMA4_READY 0x194
+#define DMA_READY(chan) (DMA_BREG(DMA0_READY, chan))
+
+#define DMA_GLOBAL_REGISTER 0x908
+
+#define FIFO_SIZES 0xa00
+
+#define FIFO_CONTROL 0xa10
+#define GRF_FLUSH (1<<4)
+#define ITF_FLUSH (1<<3)
+#define ATF_FLUSH (1<<2)
+
+#define FIFO_XMIT_THRESHOLD 0xa14
+
+#define DMA0_WORD0_CMP_VALUE 0xb00
+#define DMA1_WORD0_CMP_VALUE 0xb10
+#define DMA2_WORD0_CMP_VALUE 0xb20
+#define DMA3_WORD0_CMP_VALUE 0xb30
+#define DMA4_WORD0_CMP_VALUE 0xb40
+#define DMA_WORD0_CMP_VALUE(chan) (DMA_SREG(DMA0_WORD0_CMP_VALUE, chan))
+
+#define DMA0_WORD0_CMP_ENABLE 0xb04
+#define DMA1_WORD0_CMP_ENABLE 0xb14
+#define DMA2_WORD0_CMP_ENABLE 0xb24
+#define DMA3_WORD0_CMP_ENABLE 0xb34
+#define DMA4_WORD0_CMP_ENABLE 0xb44
+#define DMA_WORD0_CMP_ENABLE(chan) (DMA_SREG(DMA0_WORD0_CMP_ENABLE,chan))
+
+#define DMA0_WORD1_CMP_VALUE 0xb08
+#define DMA1_WORD1_CMP_VALUE 0xb18
+#define DMA2_WORD1_CMP_VALUE 0xb28
+#define DMA3_WORD1_CMP_VALUE 0xb38
+#define DMA4_WORD1_CMP_VALUE 0xb48
+#define DMA_WORD1_CMP_VALUE(chan) (DMA_SREG(DMA0_WORD1_CMP_VALUE, chan))
+
+#define DMA0_WORD1_CMP_ENABLE 0xb0c
+#define DMA1_WORD1_CMP_ENABLE 0xb1c
+#define DMA2_WORD1_CMP_ENABLE 0xb2c
+#define DMA3_WORD1_CMP_ENABLE 0xb3c
+#define DMA4_WORD1_CMP_ENABLE 0xb4c
+#define DMA_WORD1_CMP_ENABLE(chan) (DMA_SREG(DMA0_WORD1_CMP_ENABLE,chan))
+/* word 1 compare enable flags */
+#define DMA_WORD1_CMP_MATCH_OTHERBUS (1<<15)
+#define DMA_WORD1_CMP_MATCH_BROADCAST (1<<14)
+#define DMA_WORD1_CMP_MATCH_BUS_BCAST (1<<13)
+#define DMA_WORD1_CMP_MATCH_NODE_BCAST (1<<12)
+#define DMA_WORD1_CMP_MATCH_LOCAL (1<<11)
+#define DMA_WORD1_CMP_ENABLE_SELF_ID (1<<10)
+#define DMA_WORD1_CMP_ENABLE_MASTER (1<<8)
+
+#define LINK_ID 0xf00
+#define LINK_ID_BUS(id) (id<<22)
+#define LINK_ID_NODE(id) (id<<16)
+
+#define LINK_CONTROL 0xf04
+#define LINK_CONTROL_BUSY (1<<29)
+#define LINK_CONTROL_TX_ISO_EN (1<<26)
+#define LINK_CONTROL_RX_ISO_EN (1<<25)
+#define LINK_CONTROL_TX_ASYNC_EN (1<<24)
+#define LINK_CONTROL_RX_ASYNC_EN (1<<23)
+#define LINK_CONTROL_RESET_TX (1<<21)
+#define LINK_CONTROL_RESET_RX (1<<20)
+#define LINK_CONTROL_CYCMASTER (1<<11)
+#define LINK_CONTROL_CYCSOURCE (1<<10)
+#define LINK_CONTROL_CYCTIMEREN (1<<9)
+#define LINK_CONTROL_RCV_CMP_VALID (1<<7)
+#define LINK_CONTROL_SNOOP_ENABLE (1<<6)
+
+#define CYCLE_TIMER 0xf08
+
+#define LINK_PHY 0xf0c
+#define LINK_PHY_READ (1<<31)
+#define LINK_PHY_WRITE (1<<30)
+#define LINK_PHY_ADDR(addr) (addr<<24)
+#define LINK_PHY_WDATA(data) (data<<16)
+#define LINK_PHY_RADDR(addr) (addr<<8)
+
+
+#define LINK_INT_STATUS 0xf14
+#define LINK_INT_ENABLE 0xf18
+/* status and enable have identical bit numbers */
+#define LINK_INT_LINK_INT (1<<31)
+#define LINK_INT_PHY_TIMEOUT (1<<30)
+#define LINK_INT_PHY_REG_RCVD (1<<29)
+#define LINK_INT_PHY_BUSRESET (1<<28)
+#define LINK_INT_TX_RDY (1<<26)
+#define LINK_INT_RX_DATA_RDY (1<<25)
+#define LINK_INT_ISO_STUCK (1<<20)
+#define LINK_INT_ASYNC_STUCK (1<<19)
+#define LINK_INT_SENT_REJECT (1<<17)
+#define LINK_INT_HDR_ERR (1<<16)
+#define LINK_INT_TX_INVALID_TC (1<<15)
+#define LINK_INT_CYC_SECOND (1<<11)
+#define LINK_INT_CYC_START (1<<10)
+#define LINK_INT_CYC_DONE (1<<9)
+#define LINK_INT_CYC_PENDING (1<<8)
+#define LINK_INT_CYC_LOST (1<<7)
+#define LINK_INT_CYC_ARB_FAILED (1<<6)
+#define LINK_INT_GRF_OVERFLOW (1<<5)
+#define LINK_INT_ITF_UNDERFLOW (1<<4)
+#define LINK_INT_ATF_UNDERFLOW (1<<3)
+#define LINK_INT_ISOARB_FAILED (1<<0)
+
+/* PHY specifics */
+#define PHY_VENDORID_TI 0x800028
+#define PHY_PRODUCTID_TSB41LV03 0x000000
+
+
+/* this is the physical layout of a PCL, its size is 128 bytes */
+struct ti_pcl {
+ u32 next;
+ u32 async_error_next;
+ u32 user_data;
+ u32 pcl_status;
+ u32 remaining_transfer_count;
+ u32 next_data_buffer;
+ struct {
+ u32 control;
+ u32 pointer;
+ } buffer[13];
+};
+
+#include <linux/stddef.h>
+#define pcloffs(MEMBER) (offsetof(struct ti_pcl, MEMBER))
+
+
+#ifdef CONFIG_IEEE1394_PCILYNX_LOCALRAM
+
+inline static void put_pcl(const struct ti_lynx *lynx, pcl_t pclid,
+ const struct ti_pcl *pcl)
+{
+ int i;
+ u32 *in = (u32 *)pcl;
+ u32 *out = (u32 *)(lynx->local_ram + pclid * sizeof(struct ti_pcl));
+
+ for (i = 0; i < 32; i++, out++, in++) {
+ writel(cpu_to_le32(*in), out);
+ }
+}
+
+inline static void get_pcl(const struct ti_lynx *lynx, pcl_t pclid,
+ struct ti_pcl *pcl)
+{
+ int i;
+ u32 *out = (u32 *)pcl;
+ u32 *in = (u32 *)(lynx->local_ram + pclid * sizeof(struct ti_pcl));
+
+ for (i = 0; i < 32; i++, out++, in++) {
+ *out = le32_to_cpu(readl(in));
+ }
+}
+
+inline static u32 pcl_bus(const struct ti_lynx *lynx, pcl_t pclid)
+{
+ return lynx->dev->resource[1].start + pclid * sizeof(struct ti_pcl);
+}
+
+#else /* CONFIG_IEEE1394_PCILYNX_LOCALRAM */
+
+inline static void put_pcl(const struct ti_lynx *lynx, pcl_t pclid,
+ const struct ti_pcl *pcl)
+{
+ memcpy_le32((u32 *)(lynx->pcl_mem + pclid * sizeof(struct ti_pcl)),
+ (u32 *)pcl, sizeof(struct ti_pcl));
+}
+
+inline static void get_pcl(const struct ti_lynx *lynx, pcl_t pclid,
+ struct ti_pcl *pcl)
+{
+ memcpy_le32((u32 *)pcl,
+ (u32 *)(lynx->pcl_mem + pclid * sizeof(struct ti_pcl)),
+ sizeof(struct ti_pcl));
+}
+
+inline static u32 pcl_bus(const struct ti_lynx *lynx, pcl_t pclid)
+{
+ return virt_to_bus(lynx->pcl_mem) + pclid * sizeof(struct ti_pcl);
+}
+
+#endif /* CONFIG_IEEE1394_PCILYNX_LOCALRAM */
+
+
+inline static void run_sub_pcl(const struct ti_lynx *lynx, pcl_t pclid, int idx,
+ int dmachan)
+{
+ reg_write(lynx, DMA0_CURRENT_PCL + dmachan * 0x20,
+ pcl_bus(lynx, pclid) + idx * 4);
+ reg_write(lynx, DMA0_CHAN_CTRL + dmachan * 0x20,
+ DMA_CHAN_CTRL_ENABLE | DMA_CHAN_CTRL_LINK);
+}
+
+inline static void run_pcl(const struct ti_lynx *lynx, pcl_t pclid, int dmachan)
+{
+ run_sub_pcl(lynx, pclid, 0, dmachan);
+}
+
+#define PCL_NEXT_INVALID (1<<0)
+
+/* transfer commands */
+#define PCL_CMD_RCV (0x1<<24)
+#define PCL_CMD_RCV_AND_UPDATE (0xa<<24)
+#define PCL_CMD_XMT (0x2<<24)
+#define PCL_CMD_UNFXMT (0xc<<24)
+#define PCL_CMD_PCI_TO_LBUS (0x8<<24)
+#define PCL_CMD_LBUS_TO_PCI (0x9<<24)
+
+/* aux commands */
+#define PCL_CMD_NOP (0x0<<24)
+#define PCL_CMD_LOAD (0x3<<24)
+#define PCL_CMD_STOREQ (0x4<<24)
+#define PCL_CMD_STORED (0xb<<24)
+#define PCL_CMD_STORE0 (0x5<<24)
+#define PCL_CMD_STORE1 (0x6<<24)
+#define PCL_CMD_COMPARE (0xe<<24)
+#define PCL_CMD_SWAP_COMPARE (0xf<<24)
+#define PCL_CMD_ADD (0xd<<24)
+#define PCL_CMD_BRANCH (0x7<<24)
+
+/* BRANCH condition codes */
+#define PCL_COND_DMARDY_SET (0x1<<20)
+#define PCL_COND_DMARDY_CLEAR (0x2<<20)
+
+#define PCL_GEN_INTR (1<<19)
+#define PCL_LAST_BUFF (1<<18)
+#define PCL_LAST_CMD (PCL_LAST_BUFF)
+#define PCL_WAITSTAT (1<<17)
+#define PCL_BIGENDIAN (1<<16)
+
+
+quadlet_t lynx_csr_rom[] = {
+ /* bus info block */
+ 0x04040000, /* info/CRC length, CRC */
+ 0x31333934, /* 1394 magic number */
+ 0xf064a000, /* misc. settings */
+ 0x08002850, /* vendor ID, chip ID high */
+ 0x0000ffff, /* chip ID low */
+ /* root directory */
+ 0x00090000, /* CRC length, CRC */
+ 0x03080028, /* vendor ID (Texas Instr.) */
+ 0x81000009, /* offset to textual ID */
+ 0x0c000200, /* node capabilities */
+ 0x8d00000e, /* offset to unique ID */
+ 0xc7000010, /* offset to module independent info */
+ 0x04000000, /* module hardware version */
+ 0x81000026, /* offset to textual ID */
+ 0x09000000, /* node hardware version */
+ 0x81000026, /* offset to textual ID */
+ /* module vendor ID textual */
+ 0x00080000, /* CRC length, CRC */
+ 0x00000000,
+ 0x00000000,
+ 0x54455841, /* "Texas Instruments" */
+ 0x5320494e,
+ 0x53545255,
+ 0x4d454e54,
+ 0x53000000,
+ /* node unique ID leaf */
+ 0x00020000, /* CRC length, CRC */
+ 0x08002850, /* vendor ID, chip ID high */
+ 0x0000ffff, /* chip ID low */
+ /* module dependent info */
+ 0x00060000, /* CRC length, CRC */
+ 0xb8000006, /* offset to module textual ID */
+ 0x81000004, /* ??? textual descriptor */
+ 0x39010000, /* SRAM size */
+ 0x3a010000, /* AUXRAM size */
+ 0x3b000000, /* AUX device */
+ /* module textual ID */
+ 0x00050000, /* CRC length, CRC */
+ 0x00000000,
+ 0x00000000,
+ 0x54534231, /* "TSB12LV21" */
+ 0x324c5632,
+ 0x31000000,
+ /* part number */
+ 0x00060000, /* CRC length, CRC */
+ 0x00000000,
+ 0x00000000,
+ 0x39383036, /* "9806000-0001" */
+ 0x3030342d,
+ 0x30303431,
+ 0x20000001,
+ /* module hardware version textual */
+ 0x00050000, /* CRC length, CRC */
+ 0x00000000,
+ 0x00000000,
+ 0x5453424b, /* "TSBKPCITST" */
+ 0x50434954,
+ 0x53540000,
+ /* node hardware version textual */
+ 0x00050000, /* CRC length, CRC */
+ 0x00000000,
+ 0x00000000,
+ 0x54534232, /* "TSB21LV03" */
+ 0x313c5630,
+ 0x33000000
+};
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)