Internet-Draft IOAM-DEX Over MNA June 2024
Mirsky, et al. Expires 27 December 2024 [Page]
Workgroup:
MPLS Working Group
Internet-Draft:
draft-mb-mpls-ioam-dex-07
Published:
Intended Status:
Standards Track
Expires:
Authors:
G. Mirsky
Ericsson
M. Boucadair
Orange
T. Li
Juniper Networks

Supporting In-Situ Operations, Administration, and Maintenance Direct Export Using MPLS Network Actions

Abstract

In-Situ Operations, Administration, and Maintenance (IOAM), defined in RFC 9197, is an on-path telemetry method to collect and transport the operational state and telemetry information that can be used to calculate various performance metrics. IOAM Direct Export (IOAM-DEX) is one of the IOAM Option types, in which the operational state and telemetry information are collected according to the specified profile and exported in a manner and format defined by a local policy. MPLS Network Actions (MNA) techniques are meant to indicate actions to be performed on any combination of Label Switched Paths (LSPs), MPLS packets, and the node itself, and also to transfer data needed for these actions. This document explores the on-path operational state, and telemetry information can be collected using IOAM-DEX Option in combination with MNA.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 27 December 2024.

Table of Contents

1. Introduction

In-Situ OAM (IOAM) [RFC9197] is an on-path telemetry method to collect and transport the operational state and telemetry information that can be used to calculate various performance metrics. Several IOAM Option types (e.g., Pre-allocated and Incremental) use the user packet to collect the operational state and telemetry information. Such a mechanism transports the collected information to an IOAM decapsulating node (typically located at the edge of the IOAM domain within the data packet). IOAM Direct Export (IOAM-DEX) [RFC9326] is an IOAM Option type. In IOAM-DEX, the operational state and telemetry information are collected according to the specified profile and exported in a manner and format defined by a local policy. MPLS Network Actions (MNA) techniques [I-D.ietf-mpls-mna-fwk] indicate actions to be performed on any combination of Label Switched Paths (LSPs), MPLS packets, the node itself, and also allow for the transfer of data needed for these actions.

This document describes how MNA can be used for collecting on-path operational state and telemetry information using IOAM-DEX Option. Specifying the mechanism of exporting collected information is outside the scope of this document.

2. Conventions Used in this Document

2.1. Acronyms

IOAM: In-Situ OAM

IOAM-DEX: IOAM Direct Export

IOAM-DEX-MNA: IOAM Direct Export in MPLS Network Action

ISD: In-Stack Data

LSP: Label Switched Path

LSE: Label Stack Entry

MPLS: Multiprotocol Label Switching

MNA: MPLS Network Action

NAI: Network Action Indicator

2.2. Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

3. Applicability of IOAM Option Types in an MPLS Network

Pre-allocated, Incremental, and Edge-to-Edge IOAM Option types [RFC9197] use user packets to collect and transport the operational state and telemetry information. In some environments, for example, data center networks, this technique is useful as the available bandwidth and the use of jumbo frames can accommodate the increase of the packet payload. But for other use cases in which network resources are closely controlled, the use of in-band channels for collecting and transporting the telemetry information may noticeably decrease the cost-efficiency of network operations. Although the operational state and telemetry information are essential for network automation (Section 4 of [RFC8969]), its delivery is not as critical as user packets. As such, collecting and transporting the operational state and telemetry information out-of-band using the management plane is a viable option for some environments. IOAM-DEX [RFC9326] is used to collect IOAM data defined in [RFC9197]. The processing and transport of the collected information are controlled by a local policy which is outside the scope of this specification. The performance considerations discussed in Section 5 of [RFC9326] are applicable here.

4. Realization of IOAM-DEX as an MPLS Network Action

4.1. IOAM-DEX Format for an MPLS Network

[I-D.ietf-mpls-mna-usecases] recognizes the importance of IOAM in MPLS networks and lists it as one of the use cases that might be supported using MNA techniques. [I-D.ietf-mpls-mna-fwk] defines the architectural elements that compose MNA. This document uses all the elements of the IOAM-DEX Option-Type format defined in [RFC9326] to support IOAM-DEX in an MPLS network using MPLS Network Action (MNA) framework [I-D.ietf-mpls-mna-fwk] and architecture as in-stack data (ISD) MNA [I-D.ietf-mpls-mna-hdr]. The IOAM-DEX in MNA header is using LSE Format D, as defined in Section 4.4 [I-D.ietf-mpls-mna-hdr] mapping IOAM-DEX Optin Type format [RFC9326]. In addition to the requirement to preserve the Bottom of Stack field, the most significant bit in LSE Format D is always set to 1 avoiding a possible mix-up of the LSE with one of the Base Special Purpose Labels. The format of IOAM-DEX in MNA is shown in Figure 1.

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|         Namespace-ID          |    Resv   |S|     Flags     |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|            IOAM-Trace-Type-MNA            |S|O|R| Ext-Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|           Flow ID MNA (Optional)          |S|     Resv      |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|       Sequence Number MNA (Optional)      |S|     Resv      |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Figure 1: IOAM Direct Export Option Type Format in an MPLS Network Action Framework

Where fields are defined as follows:

  • Namespace-ID is a 16-bit identifier of the IOAM Namespace, as defined in [RFC9197].
  • S is a one-bit the Bottom of Stack [RFC3032].
  • Flags is an eight-bit field comprised of eight one-bit subfields. The subfields in the Flags field are allocated by IANA in IOAM DEX Flags registry, as defined in Section 4.2 of [RFC9326].
  • IOAM-Trace-Type-MNA is a 22-bit field. The interpretation of bit positions in the IOAM-Trace-Type-MNA is as specified in IANA's IOAM Trace-Type registry [IANA-IOAM-Trace-Type] from Bit 0 through Bit 21.
  • O is the one-bit flag identical to the interpretation of Bit 22 variable-length Opaque State Snapshot in IANA's IOAM Trace-Type registry [IANA-IOAM-Trace-Type].
  • R (Reserved) is a one-bit flag identical to the interpretation of Bit 23 in IANA's IOAM Trace-Type registry [IANA-IOAM-Trace-Type]. It MUST be zeroed on the transmission and ignored on receipt. Similarly to [RFC9197], it is reserved to allow for future extensions of the IOAM-Trace-Type-MNA bit field.
  • The concatenation of IOAM-Trace-Type-MNA, O, and R fields, explained above, is identical to IOAM-Trace-Type in the interpretation of its bits, assigned in IANA's IOAM Trace-Type registry [IANA-IOAM-Trace-Type]. Also, note that the Bit 7 field, i.e., checksum complement, is handled as defined in [RFC9326].
  • Ext-Flags is a six-bit field comprised of six one-bit subfields. The allocation of the subfields in the Ext-Flags field is according to Section 4.3 of [RFC9326]. The allocated flags indicate the presence of the optional Flow ID and/or Sequence Number fields in the IOAM-DEX-MNA header. The length of the Ext-Flags field in IOAM-DEX Option-Type in MNA is shorter by two one-bit fields compared to the length of the Extension Flags field defined in Section 3.2 of [RFC9326]. Mapping of these two bit positins is for further study. Figure 2 displays the detailed format of the Ext-Flags field.
  • Optional fields, i.e., Flow ID and Sequence Number, according to [RFC9326], immediately follow the Reserved field used to align optional fields at the four-octet word boundary. In the case of IOAM-DEX in MNA, such alignment can be achieved without using padding.
  • Flow ID MNA is an optional 22-bit field. The semantics of the Flow ID MNA field is as of the Flow ID field defined in Section 3.2 of [RFC9326].
  • Sequence Number - is an optional 22-bit field. The semantics of the Sequence Number MNA field is as of the Sequence Number field defined in Section 3.2 of [RFC9326]. Although the length of the Sequence Number field in IOAM-DEX in MNA is 22 bit-long smaller than the 32-bit length allotted in [RFC9326], there is sufficient space before the rollover so that its value, in combination with the value of the Flow ID field, can be used to correlate the exported data generated by the same trigger packet carrying IOAM-DEX MNA.
  • Resv fields MUST be zeroed on transmit and ignored on receipt.
 0 1 2 3 4 5
+-+-+-+-+-+-+
|F|S|U|U|U|U|
+-+-+-+-+-+-+
Figure 2: Ext-Flags Field Format

Where fields are defined as follows:

  • F - one-bit flag. When the flag is set to 1, it indicates the presence of the Flow ID field in the IOAM-DEX-MNA header.
  • S - one-bit flag. When the flag is set to 1, it indicates the presence of the Sequence Number field in the IOAM-DEX-MNA header.
  • U - unassigned one-bit flag. It MUST be zeroed on transmission and the value MUST be ignored upon receipt.

4.2. IOAM-DEX-MNA Encoding as In-Stack Data MPLS Network Action

To support the direct export of the operational state and telemetry information, the IOAM-DEX-MNA blob (binary large object), as shown in Figure 1 can be placed as part of the ISD block in an MPLS label stack according to the MNA encoding principles defined in [I-D.ietf-mpls-mna-hdr]. Using the IHS field, the IOAM-DEX-MNA can be performed in Hop-by-Hop, Ingress-to-Egress, or Select modes [I-D.ietf-mpls-mna-fwk] of collecting the operational state and telemetry information, as MNA Opcode (Figure 3). Policies controlling the processing of the collected operational state and telemetry information, and its transport are outside the scope of this document.

 0                   1                   2                   3
 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|               MNA bSPL                | TC  |S|    TTL        |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Opcode = TBA1 |        Data           |P|IHS|S| Res |U|  NASL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~                         IOAM-DEX-MNA                          ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: An Example of IOAM-DEX Encapsulation as an MNA Opcode

Where the enclosed elements are defined as follows:

  • MNA bSPL is a base Special Purpose Label assigned by IANA per the request in [I-D.ietf-mpls-mna-hdr].
  • S - the Bottom of Stack field [RFC3032].
  • P, IHS, Res, U, and NASL fields are as specified in Section 4.2 of [I-D.ietf-mpls-mna-hdr].
  • NASL - number of LSEs that compose the IOAM-DEX-MNA blob.
  • Opcode is MNA-IOAM-DEX opcode (TBA1) assigned by IANA Section 5.1.
  • IOAM-DEX-MNA - IOAM Direct Export in MPLS Network Action encoding

5. IANA Considerations

5.1. IOAM-DEX-MNA as an MPLS Network Action Opcode

IANA is requested to assign an IOAM-DEX-MNA codepoint (TBA1) from its Network Action Opcodes registry (creation requested in [I-D.ietf-mpls-mna-hdr]) as specified in Table 1.

Table 1: IOAM-DEX as MPLS Network Action Opcode
Opcode Description Reference
TBA1 IOAM-DEX as MPLS Network Action Indicator This document

6. Security Considerations

Security considerations discussed in [RFC9197], [RFC9326], and [I-D.ietf-mpls-mna-fwk] apply to this document.

7. Acknowledgments

The authors exxpress their sincereappreciation to Loa Andersson for his thorough review and thoughtful suggestion that helped in improving this document.

8. References

8.1. Normative References

[I-D.ietf-mpls-mna-fwk]
Andersson, L., Bryant, S., Bocci, M., and T. Li, "MPLS Network Actions (MNA) Framework", Work in Progress, Internet-Draft, draft-ietf-mpls-mna-fwk-09, , <https://datatracker.ietf.org/doc/html/draft-ietf-mpls-mna-fwk-09>.
[I-D.ietf-mpls-mna-hdr]
Rajamanickam, J., Gandhi, R., Zigler, R., Song, H., and K. Kompella, "MPLS Network Action (MNA) Sub-Stack Solution", Work in Progress, Internet-Draft, draft-ietf-mpls-mna-hdr-07, , <https://datatracker.ietf.org/doc/html/draft-ietf-mpls-mna-hdr-07>.
[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC3032]
Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack Encoding", RFC 3032, DOI 10.17487/RFC3032, , <https://www.rfc-editor.org/info/rfc3032>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.
[RFC9197]
Brockners, F., Ed., Bhandari, S., Ed., and T. Mizrahi, Ed., "Data Fields for In Situ Operations, Administration, and Maintenance (IOAM)", RFC 9197, DOI 10.17487/RFC9197, , <https://www.rfc-editor.org/info/rfc9197>.
[RFC9326]
Song, H., Gafni, B., Brockners, F., Bhandari, S., and T. Mizrahi, "In Situ Operations, Administration, and Maintenance (IOAM) Direct Exporting", RFC 9326, DOI 10.17487/RFC9326, , <https://www.rfc-editor.org/info/rfc9326>.

8.2. Informational References

[I-D.ietf-mpls-mna-usecases]
Saad, T., Makhijani, K., Song, H., and G. Mirsky, "Use Cases for MPLS Network Action Indicators and MPLS Ancillary Data", Work in Progress, Internet-Draft, draft-ietf-mpls-mna-usecases-10, , <https://datatracker.ietf.org/doc/html/draft-ietf-mpls-mna-usecases-10>.
[IANA-IOAM-Trace-Type]
IANA, "IOAM Trace-Type", <https://www.iana.org/assignments/ioam/ioam.xhtml#trace-type>.
[RFC8969]
Wu, Q., Ed., Boucadair, M., Ed., Lopez, D., Xie, C., and L. Geng, "A Framework for Automating Service and Network Management with YANG", RFC 8969, DOI 10.17487/RFC8969, , <https://www.rfc-editor.org/info/rfc8969>.

Authors' Addresses

Greg Mirsky
Ericsson
Mohamed Boucadair
Orange
35000 Rennes
France
Tony Li
Juniper Networks