patch-2.0.35 linux/drivers/block/paride/epia.c

Next file: linux/drivers/block/paride/fit2.c
Previous file: linux/drivers/block/paride/epat.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.0.34/linux/drivers/block/paride/epia.c linux/drivers/block/paride/epia.c
@@ -0,0 +1,326 @@
+/* 
+        epia.c    (c) 1997-8  Grant R. Guenther <grant@torque.net>
+                              Under the terms of the GNU public license.
+
+        epia.c is a low-level protocol driver for Shuttle Technologies 
+	EPIA parallel to IDE adapter chip.  This device is now obsolete
+	and has been replaced with the EPAT chip, which is supported
+	by epat.c, however, some devices based on EPIA are still
+	available.
+
+*/
+
+/* Changes:
+
+        1.01    GRG 1998.05.06 init_proto, release_proto
+	1.02    GRG 1998.06.17 support older versions of EPIA
+
+*/
+
+#define EPIA_VERSION      "1.02"
+
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <asm/io.h>
+
+#include "paride.h"
+
+/* mode codes:  0  nybble reads on port 1, 8-bit writes
+                1  5/3 reads on ports 1 & 2, 8-bit writes
+                2  8-bit reads and writes
+                3  8-bit EPP mode
+		4  16-bit EPP
+		5  32-bit EPP
+*/
+
+#define j44(a,b)                (((a>>4)&0x0f)+(b&0xf0))
+#define j53(a,b)                (((a>>3)&0x1f)+((b<<4)&0xe0))
+
+/* cont =  0   IDE register file
+   cont =  1   IDE control registers
+*/
+
+static int cont_map[2] = { 0, 0x80 };
+
+static int epia_read_regr( PIA *pi, int cont, int regr )
+
+{       int     a, b, r;
+
+	regr += cont_map[cont];
+
+        switch (pi->mode)  {
+
+        case 0: r = regr^0x39;
+                w0(r); w2(1); w2(3); w0(r);
+                a = r1(); w2(1); b = r1(); w2(4);
+                return j44(a,b);
+
+        case 1: r = regr^0x31;
+                w0(r); w2(1); w0(r&0x37); 
+                w2(3); w2(5); w0(r|0xf0);
+                a = r1(); b = r2(); w2(4);
+                return j53(a,b);
+
+        case 2: r = regr^0x29;
+                w0(r); w2(1); w2(0X21); w2(0x23); 
+                a = r0(); w2(4);
+                return a;
+
+	case 3:
+	case 4:
+        case 5: w3(regr); w2(0x24); a = r4(); w2(4);
+                return a;
+
+        }
+        return -1;
+}       
+
+static void epia_write_regr( PIA *pi, int cont, int regr, int val)
+
+{       int  r;
+
+	regr += cont_map[cont];
+
+        switch (pi->mode)  {
+
+        case 0:
+        case 1:
+        case 2: r = regr^0x19;
+                w0(r); w2(1); w0(val); w2(3); w2(4);
+                break;
+
+	case 3:
+	case 4:
+        case 5: r = regr^0x40;
+                w3(r); w4(val); w2(4);
+                break;
+        }
+}
+
+#define WR(r,v)         epia_write_regr(pi,0,r,v)
+#define RR(r)           (epia_read_regr(pi,0,r))
+
+/* The use of register 0x84 is entirely unclear - it seems to control
+   some EPP counters ...  currently we know about 3 different block
+   sizes:  the standard 512 byte reads and writes, 12 byte writes and 
+   2048 byte reads (the last two being used in the CDrom drivers.
+*/
+
+static void epia_connect ( PIA *pi  )
+
+{       pi->saved_r0 = r0();
+        pi->saved_r2 = r2();
+
+        w2(4); w0(0xa0); w0(0x50); w0(0xc0); w0(0x30); w0(0xa0); w0(0);
+        w2(1); w2(4);
+        if (pi->mode >= 3) { 
+                w0(0xa); w2(1); w2(4); w0(0x82); w2(4); w2(0xc); w2(4);
+                w2(0x24); w2(0x26); w2(4);
+        }
+        WR(0x86,8);  
+}
+
+static void epia_disconnect ( PIA *pi )
+
+{       /* WR(0x84,0x10); */
+        w0(pi->saved_r0);
+        w2(1); w2(4);
+        w0(pi->saved_r0);
+        w2(pi->saved_r2);
+} 
+
+static void epia_read_block( PIA *pi, char * buf, int count )
+
+{       int     k, ph, a, b;
+
+        switch (pi->mode) {
+
+        case 0: w0(0x81); w2(1); w2(3); w0(0xc1);
+                ph = 1;
+                for (k=0;k<count;k++) {
+                        w2(2+ph); a = r1();
+                        w2(4+ph); b = r1();
+                        buf[k] = j44(a,b);
+                        ph = 1 - ph;
+                } 
+                w0(0); w2(4);
+                break;
+
+        case 1: w0(0x91); w2(1); w0(0x10); w2(3); 
+                w0(0x51); w2(5); w0(0xd1); 
+                ph = 1;
+                for (k=0;k<count;k++) {
+                        w2(4+ph);
+                        a = r1(); b = r2();
+                        buf[k] = j53(a,b);
+                        ph = 1 - ph;
+                }
+                w0(0); w2(4);
+                break;
+
+        case 2: w0(0x89); w2(1); w2(0x23); w2(0x21); 
+                ph = 1;
+                for (k=0;k<count;k++) {
+                        w2(0x24+ph);
+                        buf[k] = r0();
+                        ph = 1 - ph;
+                }
+                w2(6); w2(4);
+                break;
+
+        case 3: if (count > 512) WR(0x84,3);
+		w3(0); w2(0x24);
+                for (k=0;k<count;k++) buf[k] = r4();
+                w2(4); WR(0x84,0);
+                break;
+
+        case 4: if (count > 512) WR(0x84,3);
+		w3(0); w2(0x24);
+		for (k=0;k<count/2;k++) ((u16 *)buf)[k] = r4w();
+                w2(4); WR(0x84,0);
+                break;
+
+        case 5: if (count > 512) WR(0x84,3);
+		w3(0); w2(0x24);
+                for (k=0;k<count/4;k++) ((u32 *)buf)[k] = r4l();
+                w2(4); WR(0x84,0);
+                break;
+
+        }
+}
+
+static void epia_write_block( PIA *pi, char * buf, int count )
+
+{       int     ph, k, last, d;
+
+        switch (pi->mode) {
+
+        case 0:
+        case 1:
+        case 2: w0(0xa1); w2(1); w2(3); w2(1); w2(5);
+                ph = 0;  last = 0x8000;
+                for (k=0;k<count;k++) {
+                        d = buf[k];
+                        if (d != last) { last = d; w0(d); }
+                        w2(4+ph);
+                        ph = 1 - ph;
+                }
+                w2(7); w2(4);
+                break;
+
+        case 3: if (count < 512) WR(0x84,1);
+		w3(0x40);
+                for (k=0;k<count;k++) w4(buf[k]);
+		if (count < 512) WR(0x84,0);
+                break;
+
+        case 4: if (count < 512) WR(0x84,1);
+		w3(0x40);
+                for (k=0;k<count/2;k++) w4w(((u16 *)buf)[k]);
+		if (count < 512) WR(0x84,0);
+                break;
+
+        case 5: if (count < 512) WR(0x84,1);
+		w3(0x40);
+                for (k=0;k<count/4;k++) w4l(((u32 *)buf)[k]);
+		if (count < 512) WR(0x84,0);
+                break;
+
+        }
+
+}
+
+static int epia_test_proto( PIA *pi, char * scratch, int verbose )
+
+{       int     j, k, f;
+	int	e[2] = {0,0};
+
+        epia_connect(pi);
+        for (j=0;j<2;j++) {
+            WR(6,0xa0+j*0x10);
+            for (k=0;k<256;k++) {
+                WR(2,k^0xaa);
+                WR(3,k^0x55);
+                if (RR(2) != (k^0xaa)) e[j]++;
+            }
+	    WR(2,1); WR(3,1);
+        }
+        epia_disconnect(pi);
+
+        f = 0;
+        epia_connect(pi);
+        WR(0x84,8);
+        epia_read_block(pi,scratch,512);
+        for (k=0;k<256;k++) {
+            if ((scratch[2*k] & 0xff) != ((k+1) & 0xff)) f++;
+            if ((scratch[2*k+1] & 0xff) != ((-2-k) & 0xff)) f++;
+        }
+        WR(0x84,0);
+        epia_disconnect(pi);
+
+        if (verbose)  {
+            printk("%s: epia: port 0x%x, mode %d, test=(%d,%d,%d)\n",
+                   pi->device,pi->port,pi->mode,e[0],e[1],f);
+        }
+        
+        return (e[0] && e[1]) || f;
+
+}
+
+
+static void epia_log_adapter( PIA *pi, char * scratch, int verbose )
+
+{       char    *mode_string[6] = {"4-bit","5/3","8-bit",
+				   "EPP-8","EPP-16","EPP-32"};
+
+        printk("%s: epia %s, Shuttle EPIA at 0x%x, ",
+                pi->device,EPIA_VERSION,pi->port);
+        printk("mode %d (%s), delay %d\n",pi->mode,
+		mode_string[pi->mode],pi->delay);
+
+}
+
+static void epia_init_proto( PIA *pi)
+
+{       MOD_INC_USE_COUNT;
+}
+
+static void epia_release_proto( PIA *pi)
+
+{       MOD_DEC_USE_COUNT;
+}
+
+struct pi_protocol epia = {"epia",0,6,3,1,1,
+                           epia_write_regr,
+                           epia_read_regr,
+                           epia_write_block,
+                           epia_read_block,
+                           epia_connect,
+                           epia_disconnect,
+                           0,
+                           0,
+                           epia_test_proto,
+                           epia_log_adapter,
+                           epia_init_proto,
+                           epia_release_proto
+                          };
+
+
+#ifdef MODULE
+
+int     init_module(void)
+
+{       return pi_register( &epia ) - 1;
+}
+
+void    cleanup_module(void)
+
+{       pi_unregister( &epia );
+}
+
+#endif
+
+/* end of epia.c */
+

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov