patch-2.0.31 linux/drivers/scsi/tmscsim.h

Next file: linux/drivers/scsi/u14-34f.c
Previous file: linux/drivers/scsi/tmscsim.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.0.30/linux/drivers/scsi/tmscsim.h linux/drivers/scsi/tmscsim.h
@@ -0,0 +1,680 @@
+/***********************************************************************
+;*	File Name : TMSCSIM.H					       *
+;*		    TEKRAM DC-390(T) PCI SCSI Bus Master Host Adapter  *
+;*		    Device Driver				       *
+;***********************************************************************/
+
+#ifndef TMSCSIM_H
+#define TMSCSIM_H
+
+#define IRQ_NONE 255
+
+typedef unsigned char	UCHAR;
+typedef unsigned short	USHORT;
+typedef unsigned long	ULONG;
+typedef unsigned int	UINT;
+
+typedef UCHAR		*PUCHAR;
+typedef USHORT		*PUSHORT;
+typedef ULONG		*PULONG;
+typedef Scsi_Host_Template  *PSHT;
+typedef struct Scsi_Host    *PSH;
+typedef Scsi_Device	*PSCSIDEV;
+typedef Scsi_Cmnd	*PSCSICMD;
+typedef void		*PVOID;
+typedef struct scatterlist  *PSGL, SGL;
+
+
+/*;-----------------------------------------------------------------------*/
+typedef  struct  _SyncMsg
+{
+UCHAR		ExtendMsg;
+UCHAR		ExtMsgLen;
+UCHAR		SyncXferReq;
+UCHAR		Period;
+UCHAR		ReqOffset;
+} SyncMsg;
+/*;-----------------------------------------------------------------------*/
+typedef  struct  _Capacity
+{
+ULONG		BlockCount;
+ULONG		BlockLength;
+} Capacity;
+/*;-----------------------------------------------------------------------*/
+typedef  struct  _SGentry
+{
+ULONG		SGXferDataPtr;
+ULONG		SGXferDataLen;
+} SGentry;
+
+typedef  struct  _SGentry1
+{
+ULONG		SGXLen;
+ULONG		SGXPtr;
+} SGentry1, *PSGE;
+
+
+#define MAX_ADAPTER_NUM 	4
+#define MAX_DEVICES		10
+#define MAX_SG_LIST_BUF 	16
+#define MAX_CMD_QUEUE		20
+#define MAX_CMD_PER_LUN 	8
+#define MAX_SCSI_ID		8
+#define MAX_SRB_CNT		MAX_CMD_QUEUE+4
+#define END_SCAN		2
+
+#define SEL_TIMEOUT		153	/* 250 ms selection timeout (@ 40 MHz) */
+
+/*
+;-----------------------------------------------------------------------
+; SCSI Request Block
+;-----------------------------------------------------------------------
+*/
+struct	_SRB
+{
+UCHAR		CmdBlock[12];
+
+struct _SRB	*pNextSRB;
+struct _DCB	*pSRBDCB;
+PSCSICMD	pcmd;
+PSGL		pSegmentList;
+
+ULONG		PhysSRB;
+ULONG		TotalXferredLen;
+ULONG		SGPhysAddr;	/*;a segment starting address */
+ULONG		SGToBeXferLen;	/*; to be xfer length */
+
+SGL		Segmentx;	/* make a one entry of S/G list table */
+
+PUCHAR		pMsgPtr;
+USHORT		SRBState;
+USHORT		Revxx2; 	/* ??? */
+
+UCHAR		MsgInBuf[6];
+UCHAR		MsgOutBuf[6];
+
+UCHAR		AdaptStatus;
+UCHAR		TargetStatus;
+UCHAR		MsgCnt;
+UCHAR		EndMessage;
+UCHAR		TagNumber;
+UCHAR		SGcount;
+UCHAR		SGIndex;
+UCHAR		IORBFlag;	/*;81h-Reset, 2-retry */
+
+UCHAR		SRBStatus;
+UCHAR		RetryCnt;
+UCHAR		SRBFlag;	/*; b0-AutoReqSense,b6-Read,b7-write */
+				/*; b4-settimeout,b5-Residual valid */
+UCHAR		ScsiCmdLen;
+UCHAR		ScsiPhase;
+UCHAR		Reserved3[3];	/*;for dword alignment */
+ULONG		Segment0[2];
+ULONG		Segment1[2];
+};
+
+typedef  struct  _SRB	 DC390_SRB, *PSRB;
+
+/*
+;-----------------------------------------------------------------------
+; Device Control Block
+;-----------------------------------------------------------------------
+*/
+struct	_DCB
+{
+struct _DCB	*pNextDCB;
+struct _ACB	*pDCBACB;
+
+PSCSICMD	pQIORBhead;
+PSCSICMD	pQIORBtail;
+PSCSICMD	AboIORBhead;
+PSCSICMD	AboIORBtail;
+USHORT		QIORBCnt;
+USHORT		AboIORBcnt;
+
+PSRB		pWaitingSRB;
+PSRB		pWaitLast;
+PSRB		pGoingSRB;
+PSRB		pGoingLast;
+PSRB		pActiveSRB;
+USHORT		GoingSRBCnt;
+USHORT		WaitSRBCnt;	/* ??? */
+
+ULONG		TagMask;
+
+USHORT		MaxCommand;
+USHORT		AdaptIndex;	/*; UnitInfo struc start */
+USHORT		UnitIndex;	/*; nth Unit on this card */
+UCHAR		UnitSCSIID;	/*; SCSI Target ID  (SCSI Only) */
+UCHAR		UnitSCSILUN;	/*; SCSI Log.  Unit (SCSI Only) */
+
+UCHAR		IdentifyMsg;
+UCHAR		CtrlR1;
+UCHAR		CtrlR3;
+UCHAR		CtrlR4;
+
+UCHAR		InqDataBuf[8];
+UCHAR		CapacityBuf[8];
+UCHAR		DevMode;
+UCHAR		AdpMode;
+UCHAR		SyncMode;	/*; 0:async mode */
+UCHAR		NegoPeriod;	/*;for nego. */
+UCHAR		SyncPeriod;	/*;for reg. */
+UCHAR		SyncOffset;	/*;for reg. and nego.(low nibble) */
+UCHAR		UnitCtrlFlag;
+UCHAR		DCBFlag;
+UCHAR		DevType;
+UCHAR		Reserved2[3];	/*;for dword alignment */
+};
+
+typedef  struct  _DCB	 DC390_DCB, *PDCB;
+/*
+;-----------------------------------------------------------------------
+; Adapter Control Block
+;-----------------------------------------------------------------------
+*/
+struct	_ACB
+{
+ULONG		PhysACB;
+PSH		pScsiHost;
+struct _ACB	*pNextACB;
+USHORT		IOPortBase;
+USHORT		Revxx1; 	/* ??? */
+
+PDCB		pLinkDCB;
+PDCB		pDCBRunRobin;
+PDCB		pActiveDCB;
+PDCB		pDCB_free;
+PSRB		pFreeSRB;
+PSRB		pTmpSRB;
+USHORT		SRBCount;
+USHORT		AdapterIndex;	/*; nth Adapter this driver */
+USHORT		max_id;
+USHORT		max_lun;
+
+UCHAR		msgin123[4];
+UCHAR		status;
+UCHAR		AdaptSCSIID;	/*; Adapter SCSI Target ID */
+UCHAR		AdaptSCSILUN;	/*; Adapter SCSI LUN */
+UCHAR		DeviceCnt;
+UCHAR		IRQLevel;
+UCHAR		TagMaxNum;
+UCHAR		ACBFlag;
+UCHAR		Gmode2;
+UCHAR		LUNchk;
+UCHAR		scan_devices;
+UCHAR		HostID_Bit;
+UCHAR		Reserved1[1];	/*;for dword alignment */
+UCHAR		DCBmap[MAX_SCSI_ID];
+DC390_DCB	DCB_array[MAX_DEVICES]; 	/* +74h,  Len=3E8 */
+DC390_SRB	SRB_array[MAX_SRB_CNT]; 	/* +45Ch, Len=	*/
+DC390_SRB	TmpSRB;
+};
+
+typedef  struct  _ACB	 DC390_ACB, *PACB;
+
+/*;-----------------------------------------------------------------------*/
+
+
+#define BIT31	0x80000000
+#define BIT30	0x40000000
+#define BIT29	0x20000000
+#define BIT28	0x10000000
+#define BIT27	0x08000000
+#define BIT26	0x04000000
+#define BIT25	0x02000000
+#define BIT24	0x01000000
+#define BIT23	0x00800000
+#define BIT22	0x00400000
+#define BIT21	0x00200000
+#define BIT20	0x00100000
+#define BIT19	0x00080000
+#define BIT18	0x00040000
+#define BIT17	0x00020000
+#define BIT16	0x00010000
+#define BIT15	0x00008000
+#define BIT14	0x00004000
+#define BIT13	0x00002000
+#define BIT12	0x00001000
+#define BIT11	0x00000800
+#define BIT10	0x00000400
+#define BIT9	0x00000200
+#define BIT8	0x00000100
+#define BIT7	0x00000080
+#define BIT6	0x00000040
+#define BIT5	0x00000020
+#define BIT4	0x00000010
+#define BIT3	0x00000008
+#define BIT2	0x00000004
+#define BIT1	0x00000002
+#define BIT0	0x00000001
+
+/*;---UnitCtrlFlag */
+#define UNIT_ALLOCATED	BIT0
+#define UNIT_INFO_CHANGED BIT1
+#define FORMATING_MEDIA BIT2
+#define UNIT_RETRY	BIT3
+
+/*;---UnitFlags */
+#define DASD_SUPPORT	BIT0
+#define SCSI_SUPPORT	BIT1
+#define ASPI_SUPPORT	BIT2
+
+/*;----SRBState machine definition */
+#define SRB_FREE	0
+#define SRB_WAIT	BIT0
+#define SRB_READY	BIT1
+#define SRB_MSGOUT	BIT2	/*;arbitration+msg_out 1st byte*/
+#define SRB_MSGIN	BIT3
+#define SRB_MSGIN_MULTI BIT4
+#define SRB_COMMAND	BIT5
+#define SRB_START_	BIT6	/*;arbitration+msg_out+command_out*/
+#define SRB_DISCONNECT	BIT7
+#define SRB_DATA_XFER	BIT8
+#define SRB_XFERPAD	BIT9
+#define SRB_STATUS	BIT10
+#define SRB_COMPLETED	BIT11
+#define SRB_ABORT_SENT	BIT12
+#define DO_SYNC_NEGO	BIT13
+#define SRB_UNEXPECT_RESEL BIT14
+
+/*;---ACBFlag */
+#define RESET_DEV	BIT0
+#define RESET_DETECT	BIT1
+#define RESET_DONE	BIT2
+
+/*;---DCBFlag */
+#define ABORT_DEV_	BIT0
+
+/*;---SRBstatus */
+#define SRB_OK		BIT0
+#define ABORTION	BIT1
+#define OVER_RUN	BIT2
+#define UNDER_RUN	BIT3
+#define PARITY_ERROR	BIT4
+#define SRB_ERROR	BIT5
+
+/*;---SRBFlag */
+#define DATAOUT 	BIT7
+#define DATAIN		BIT6
+#define RESIDUAL_VALID	BIT5
+#define ENABLE_TIMER	BIT4
+#define RESET_DEV0	BIT2
+#define ABORT_DEV	BIT1
+#define AUTO_REQSENSE	BIT0
+
+/*;---Adapter status */
+#define H_STATUS_GOOD	 0
+#define H_SEL_TIMEOUT	 0x11
+#define H_OVER_UNDER_RUN 0x12
+#define H_UNEXP_BUS_FREE 0x13
+#define H_TARGET_PHASE_F 0x14
+#define H_INVALID_CCB_OP 0x16
+#define H_LINK_CCB_BAD	 0x17
+#define H_BAD_TARGET_DIR 0x18
+#define H_DUPLICATE_CCB  0x19
+#define H_BAD_CCB_OR_SG  0x1A
+#define H_ABORT 	 0x0FF
+
+/*; SCSI Status byte codes*/
+#define SCSI_STAT_GOOD		0x0	/*;  Good status */
+#define SCSI_STAT_CHECKCOND	0x02	/*;  SCSI Check Condition */
+#define SCSI_STAT_CONDMET	0x04	/*;  Condition Met */
+#define SCSI_STAT_BUSY		0x08	/*;  Target busy status */
+#define SCSI_STAT_INTER 	0x10	/*;  Intermediate status */
+#define SCSI_STAT_INTERCONDMET	0x14	/*;  Intermediate condition met */
+#define SCSI_STAT_RESCONFLICT	0x18	/*;  Reservation conflict */
+#define SCSI_STAT_CMDTERM	0x22	/*;  Command Terminated */
+#define SCSI_STAT_QUEUEFULL	0x28	/*;  Queue Full */
+
+#define SCSI_STAT_UNEXP_BUS_F	0xFD	/*;  Unexpect Bus Free */
+#define SCSI_STAT_BUS_RST_DETECT 0xFE	/*;  Scsi Bus Reset detected */
+#define SCSI_STAT_SEL_TIMEOUT	0xFF	/*;  Selection Time out */
+
+/*;---Sync_Mode */
+#define SYNC_DISABLE	0
+#define SYNC_ENABLE	BIT0
+#define SYNC_NEGO_DONE	BIT1
+#define WIDE_ENABLE	BIT2
+#define WIDE_NEGO_DONE	BIT3
+#define EN_TAG_QUEUING	BIT4
+#define EN_ATN_STOP	BIT5
+
+#define SYNC_NEGO_OFFSET 15
+
+/*;---SCSI bus phase*/
+#define SCSI_DATA_OUT	0
+#define SCSI_DATA_IN	1
+#define SCSI_COMMAND	2
+#define SCSI_STATUS_	3
+#define SCSI_NOP0	4
+#define SCSI_NOP1	5
+#define SCSI_MSG_OUT	6
+#define SCSI_MSG_IN	7
+
+/*;----SCSI MSG BYTE*/
+#define MSG_COMPLETE		0x00
+#define MSG_EXTENDED		0x01
+#define MSG_SAVE_PTR		0x02
+#define MSG_RESTORE_PTR 	0x03
+#define MSG_DISCONNECT		0x04
+#define MSG_INITIATOR_ERROR	0x05
+#define MSG_ABORT		0x06
+#define MSG_REJECT_		0x07
+#define MSG_NOP 		0x08
+#define MSG_PARITY_ERROR	0x09
+#define MSG_LINK_CMD_COMPL	0x0A
+#define MSG_LINK_CMD_COMPL_FLG	0x0B
+#define MSG_BUS_RESET		0x0C
+#define MSG_ABORT_TAG		0x0D
+#define MSG_SIMPLE_QTAG 	0x20
+#define MSG_HEAD_QTAG		0x21
+#define MSG_ORDER_QTAG		0x22
+#define MSG_IDENTIFY		0x80
+#define MSG_HOST_ID		0x0C0
+
+/*;----SCSI STATUS BYTE*/
+#define STATUS_GOOD		0x00
+#define CHECK_CONDITION_	0x02
+#define STATUS_BUSY		0x08
+#define STATUS_INTERMEDIATE	0x10
+#define RESERVE_CONFLICT	0x18
+
+/* cmd->result */
+#define STATUS_MASK_		0xFF
+#define MSG_MASK		0xFF00
+#define RETURN_MASK		0xFF0000
+
+/*
+**  Inquiry Data format
+*/
+
+typedef struct	_SCSIInqData { /* INQ */
+
+	UCHAR	 DevType;		/* Periph Qualifier & Periph Dev Type*/
+	UCHAR	 RMB_TypeMod;		/* rem media bit & Dev Type Modifier */
+	UCHAR	 Vers;			/* ISO, ECMA, & ANSI versions	     */
+	UCHAR	 RDF;			/* AEN, TRMIOP, & response data format*/
+	UCHAR	 AddLen;		/* length of additional data	     */
+	UCHAR	 Res1;			/* reserved			     */
+	UCHAR	 Res2;			/* reserved			     */
+	UCHAR	 Flags; 		/* RelADr,Wbus32,Wbus16,Sync,etc.    */
+	UCHAR	 VendorID[8];		/* Vendor Identification	     */
+	UCHAR	 ProductID[16]; 	/* Product Identification	     */
+	UCHAR	 ProductRev[4]; 	/* Product Revision		     */
+
+
+} SCSI_INQDATA, *PSCSI_INQDATA;
+
+
+/*  Inquiry byte 0 masks */
+
+
+#define SCSI_DEVTYPE	    0x1F      /* Peripheral Device Type 	    */
+#define SCSI_PERIPHQUAL     0xE0      /* Peripheral Qualifier		    */
+
+
+/*  Inquiry byte 1 mask */
+
+#define SCSI_REMOVABLE_MEDIA  0x80    /* Removable Media bit (1=removable)  */
+
+
+/*  Peripheral Device Type definitions */
+
+#define SCSI_DASD		 0x00	   /* Direct-access Device	   */
+#define SCSI_SEQACESS		 0x01	   /* Sequential-access device	   */
+#define SCSI_PRINTER		 0x02	   /* Printer device		   */
+#define SCSI_PROCESSOR		 0x03	   /* Processor device		   */
+#define SCSI_WRITEONCE		 0x04	   /* Write-once device 	   */
+#define SCSI_CDROM		 0x05	   /* CD-ROM device		   */
+#define SCSI_SCANNER		 0x06	   /* Scanner device		   */
+#define SCSI_OPTICAL		 0x07	   /* Optical memory device	   */
+#define SCSI_MEDCHGR		 0x08	   /* Medium changer device	   */
+#define SCSI_COMM		 0x09	   /* Communications device	   */
+#define SCSI_NODEV		 0x1F	   /* Unknown or no device type    */
+
+/*
+** Inquiry flag definitions (Inq data byte 7)
+*/
+
+#define SCSI_INQ_RELADR       0x80    /* device supports relative addressing*/
+#define SCSI_INQ_WBUS32       0x40    /* device supports 32 bit data xfers  */
+#define SCSI_INQ_WBUS16       0x20    /* device supports 16 bit data xfers  */
+#define SCSI_INQ_SYNC	      0x10    /* device supports synchronous xfer   */
+#define SCSI_INQ_LINKED       0x08    /* device supports linked commands    */
+#define SCSI_INQ_CMDQUEUE     0x02    /* device supports command queueing   */
+#define SCSI_INQ_SFTRE	      0x01    /* device supports soft resets */
+
+
+/*
+;==========================================================
+; EEPROM byte offset
+;==========================================================
+*/
+typedef  struct  _EEprom
+{
+UCHAR	EE_MODE1;
+UCHAR	EE_SPEED;
+UCHAR	xx1;
+UCHAR	xx2;
+} EEprom, *PEEprom;
+
+#define EE_ADAPT_SCSI_ID 64
+#define EE_MODE2	65
+#define EE_DELAY	66
+#define EE_TAG_CMD_NUM	67
+
+/*; EE_MODE1 bits definition*/
+#define PARITY_CHK_	BIT0
+#define SYNC_NEGO_	BIT1
+#define EN_DISCONNECT_	BIT2
+#define SEND_START_	BIT3
+#define TAG_QUEUING_	BIT4
+
+/*; EE_MODE2 bits definition*/
+#define MORE2_DRV	BIT0
+#define GREATER_1G	BIT1
+#define RST_SCSI_BUS	BIT2
+#define ACTIVE_NEGATION BIT3
+#define NO_SEEK 	BIT4
+#define LUN_CHECK	BIT5
+
+#define ENABLE_CE	1
+#define DISABLE_CE	0
+#define EEPROM_READ	0x80
+
+/*
+;==========================================================
+;	AMD 53C974 Registers bit Definition
+;==========================================================
+*/
+/*
+;====================
+; SCSI Register
+;====================
+*/
+
+/*; Command Reg.(+0CH) */
+#define DMA_COMMAND		BIT7
+#define NOP_CMD 		0
+#define CLEAR_FIFO_CMD		1
+#define RST_DEVICE_CMD		2
+#define RST_SCSI_BUS_CMD	3
+#define INFO_XFER_CMD		0x10
+#define INITIATOR_CMD_CMPLTE	0x11
+#define MSG_ACCEPTED_CMD	0x12
+#define XFER_PAD_BYTE		0x18
+#define SET_ATN_CMD		0x1A
+#define RESET_ATN_CMD		0x1B
+#define SELECT_W_ATN		0x42
+#define SEL_W_ATN_STOP		0x43
+#define EN_SEL_RESEL		0x44
+#define SEL_W_ATN2		0x46
+#define DATA_XFER_CMD		INFO_XFER_CMD
+
+
+/*; SCSI Status Reg.(+10H) */
+#define INTERRUPT		BIT7
+#define ILLEGAL_OP_ERR		BIT6
+#define PARITY_ERR		BIT5
+#define COUNT_2_ZERO		BIT4
+#define GROUP_CODE_VALID	BIT3
+#define SCSI_PHASE_MASK 	(BIT2+BIT1+BIT0)
+
+/*; Interrupt Status Reg.(+14H) */
+#define SCSI_RESET		BIT7
+#define INVALID_CMD		BIT6
+#define DISCONNECTED		BIT5
+#define SERVICE_REQUEST 	BIT4
+#define SUCCESSFUL_OP		BIT3
+#define RESELECTED		BIT2
+#define SEL_ATTENTION		BIT1
+#define SELECTED		BIT0
+
+/*; Internal State Reg.(+18H) */
+#define SYNC_OFFSET_FLAG	BIT3
+#define INTRN_STATE_MASK	(BIT2+BIT1+BIT0)
+
+/*; Clock Factor Reg.(+24H) */
+#define CLK_FREQ_40MHZ		0
+#define CLK_FREQ_35MHZ		(BIT2+BIT1+BIT0)
+#define CLK_FREQ_30MHZ		(BIT2+BIT1)
+#define CLK_FREQ_25MHZ		(BIT2+BIT0)
+#define CLK_FREQ_20MHZ		BIT2
+#define CLK_FREQ_15MHZ		(BIT1+BIT0)
+#define CLK_FREQ_10MHZ		BIT1
+
+/*; Control Reg. 1(+20H) */
+#define EXTENDED_TIMING 	BIT7
+#define DIS_INT_ON_SCSI_RST	BIT6
+#define PARITY_ERR_REPO 	BIT4
+#define SCSI_ID_ON_BUS		(BIT2+BIT1+BIT0)
+
+/*; Control Reg. 2(+2CH) */
+#define EN_FEATURE		BIT6
+#define EN_SCSI2_CMD		BIT3
+
+/*; Control Reg. 3(+30H) */
+#define ID_MSG_CHECK		BIT7
+#define EN_QTAG_MSG		BIT6
+#define EN_GRP2_CMD		BIT5
+#define FAST_SCSI		BIT4	/* ;10MB/SEC */
+#define FAST_CLK		BIT3	/* ;25 - 40 MHZ */
+
+/*; Control Reg. 4(+34H) */
+#define EATER_12NS		0
+#define EATER_25NS		BIT7
+#define EATER_35NS		BIT6
+#define EATER_0NS		(BIT7+BIT6)
+#define NEGATE_REQACKDATA	BIT2
+#define NEGATE_REQACK		BIT3
+/*
+;====================
+; DMA Register
+;====================
+*/
+/*; DMA Command Reg.(+40H) */
+#define READ_DIRECTION		BIT7
+#define WRITE_DIRECTION 	0
+#define EN_DMA_INT		BIT6
+#define MAP_TO_MDL		BIT5
+#define DIAGNOSTIC		BIT4
+#define DMA_IDLE_CMD		0
+#define DMA_BLAST_CMD		BIT0
+#define DMA_ABORT_CMD		BIT1
+#define DMA_START_CMD		(BIT1+BIT0)
+
+/*; DMA Status Reg.(+54H) */
+#define PCI_MS_ABORT		BIT6
+#define BLAST_COMPLETE		BIT5
+#define SCSI_INTERRUPT		BIT4
+#define DMA_XFER_DONE		BIT3
+#define DMA_XFER_ABORT		BIT2
+#define DMA_XFER_ERROR		BIT1
+#define POWER_DOWN		BIT0
+
+/*
+; DMA SCSI Bus and Ctrl.(+70H)
+;EN_INT_ON_PCI_ABORT
+*/
+
+/*
+;==========================================================
+; SCSI Chip register address offset
+;==========================================================
+*/
+#define CtcReg_Low	0x00
+#define CtcReg_Mid	0x04
+#define ScsiFifo	0x08
+#define ScsiCmd 	0x0C
+#define Scsi_Status	0x10
+#define INT_Status	0x14
+#define Sync_Period	0x18
+#define Sync_Offset	0x1C
+#define CtrlReg1	0x20
+#define Clk_Factor	0x24
+#define CtrlReg2	0x2C
+#define CtrlReg3	0x30
+#define CtrlReg4	0x34
+#define CtcReg_High	0x38
+#define DMA_Cmd 	0x40
+#define DMA_XferCnt	0x44
+#define DMA_XferAddr	0x48
+#define DMA_Wk_ByteCntr 0x4C
+#define DMA_Wk_AddrCntr 0x50
+#define DMA_Status	0x54
+#define DMA_MDL_Addr	0x58
+#define DMA_Wk_MDL_Cntr 0x5C
+#define DMA_ScsiBusCtrl 0x70
+
+#define StcReg_Low	CtcReg_Low
+#define StcReg_Mid	CtcReg_Mid
+#define Scsi_Dest_ID	Scsi_Status
+#define Scsi_TimeOut	INT_Status
+#define Intern_State	Sync_Period
+#define Current_Fifo	Sync_Offset
+#define StcReg_High	CtcReg_High
+
+#define am_target	Scsi_Status
+#define am_timeout	INT_Status
+#define am_seq_step	Sync_Period
+#define am_fifo_count	Sync_Offset
+
+
+#define DC390_read8(address)			       \
+	inb(DC390_ioport + (address)))
+
+#define DC390_read16(address)			       \
+	inw(DC390_ioport + (address)))
+
+#define DC390_read32(address)			       \
+	inl(DC390_ioport + (address)))
+
+#define DC390_write8(address,value)		       \
+	outb((value), DC390_ioport + (address)))
+
+#define DC390_write16(address,value)		       \
+	outw((value), DC390_ioport + (address)))
+
+#define DC390_write32(address,value)		       \
+	outl((value), DC390_ioport + (address)))
+
+
+/* Configuration method #1 */
+#define PCI_CFG1_ADDRESS_REG		0xcf8
+#define PCI_CFG1_DATA_REG		0xcfc
+#define PCI_CFG1_ENABLE 		0x80000000
+#define PCI_CFG1_TUPPLE(bus, device, function, register)		\
+	(PCI_CFG1_ENABLE | (((bus) << 16) & 0xff0000) | 		\
+	(((device) << 11) & 0xf800) | (((function) << 8) & 0x700)|	\
+	(((register) << 2) & 0xfc))
+
+/* Configuration method #2 */
+#define PCI_CFG2_ENABLE_REG		0xcf8
+#define PCI_CFG2_FORWARD_REG		0xcfa
+#define PCI_CFG2_ENABLE 		0x0f0
+#define PCI_CFG2_TUPPLE(function)					\
+	(PCI_CFG2_ENABLE | (((function) << 1) & 0xe))
+
+
+#endif /* TMSCSIM_H */

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov